Development Boards Products

This?8051 Development Board is aimed at providing the microcontroller newbies with a quick way into the development of embedded projects. The Aryabhatta 8051 Development Board AT89S52 with Onboard USB Programmer is very easy to use but also at the same time offering high functionality and yet it is available at a price everyone can afford!!!

The All new NodeMcu ESP8266 V3 Lua CH340 Wifi Dev. Board is a fast leading edge low-cost WiFi technology. Modern high-level mature LUA based technology. It is an integrated unit with all available resources on board. It is super simple to complement your existing Arduino projects or any development board that has I/O pins available.

Ca-01 is an ultra-small package LTE Cat.1 bis module launched by Ai-Thinker. It adopts Unigroup’s UIS8910 platform and supports LTE 3GPP Rel.13 technology. It is a 4G full Netcom module that can adapt to different operators and products to ensure maximum flexibility in product design.

The ESP-01S ESP8266 WiFi Module is a self-contained SOC with integrated TCP/IP protocol stack that can give any microcontroller access to your WiFi network. The ESP8266 is capable of either hosting an application or offloading all Wi-Fi networking functions from another application processor. Each ESP-01S ESP8266 module comes pre-programmed with an AT command set firmware, meaning, you can simply hook this up to your Arduino device and get about as much WiFi-ability as a WiFi Shield offers (and that’s just out of the box)! The ESP-01S ESP8266 module is an extremely cost-effective board with a huge, and ever-growing, community. This module has a powerful enough on-board processing and storage capability that allows it to be integrated with the sensors and other application-specific devices through its GPIOs with minimal development up-front and minimal loading during runtime. Its high degree of on-chip integration allows for minimal external circuitry, including the front-end module, which is designed to occupy minimal PCB area. The ESP8266 supports APSD for VoIP applications and Bluetooth co-existence interfaces, it contains a self-calibrated RF allowing it to work under all operating conditions, and requires no external RF parts. Note: Product image may vary from the actual product in terms of IC labels

HC-05 6 Pin Wireless Serial Bluetooth Module is a Bluetooth module for use with any microcontroller. It uses the UART protocol to make it easy to send and receive data wirelessly. The HC-06 module is a slave only device. This means that it can connect to most phones and computers with Bluetooth but it cannot connect to another slave-only device such as keyboards and other HC-06 modules. To connect with other slave devices a master module would be necessary such as the HC-05 version which can do both master and slave. Applications: 1.Embedded Projects. 2.Industrial Applications. 3.Computer and Portable Devices. 4.GPS receiver.

This is USB To Serial Adapter Module USB TO TTL RS232 Arduino Cable With CTS RTS. USB To RS232 TTL PL2303HX Auto Converter Module Adapter 5V Output provides the best and convenient way to connect your RS232 TTL devices or DEMO BRD. To your computer, via the USB port. FTDI based USB to TTL Serial Cable is designed using the standard FT232RL chipset. The cables provide a fast, simple way to connect devices with a TTL level serial interface to USB. Pin Connections : Red wire： 5V Black wire： GND White wire： RXD Green wire： TXD Yellow / Brown wire： RTS Blue wire： CTS

An MB102 830 Points Solderless Prototype PCB Breadboard High Quality is an invaluable tool for experimenting with circuit designs whether in the R&D or university lab. A MB102 830 Points Solderless Prototype PCB Breadboard High Quality is used to make up temporary circuits for testing or to try out an idea. No soldering is required so it is easy to change connections and replace components. NOTE: The breadboard is slightly concave at the base. Note: The product is shown in the above images may be varied in terms of the brand.

These 65pcs Flexible Breadboard Jumper Wires are Ideal for creating circuits between your microcontroller and the breadboard on the bots Reusable for fast build a prototype of an electronic circuit. Soldering is not required. This type of breadboard cable wires is the most preferred. Wires are flexible, durable, reusable, easy to trace, easy to connect and disconnect. Quality projects deserve the use of this quality breadboard COMBO. Can modify or revise the circuits easily.

CH375 USB device mode is fully compatible with CH372, CH375 contains all the features of the CH372. Common CH375 USB host mode support USB full-speed device, the external microcontroller can through the CH375 in accordance with the USB protocol and USB device communication. CH375 firmware also built a dedicated protocol processing Mass-Storage mass storage devices, the external microcontroller can be directly used as the basic unit of reading and writing in sectors USB storage devices (including USB hard disk/USB flash drive/U disk). CH375 with the 8-bit data bus and read, write, chip select control lines and interrupt output can be easily attached to the system bus of the microcontroller/DSP/MCU/MPU controller. USB host mode, CH375 also provides serial communication via serial input, serial output, and interrupt output monolithic/DSP/MCU/MPU connected.

The FT232 WiFi Module Adapter is a compact and essential tool designed for seamless programming, downloading, and debugging of ESP8266-based ESP-01/ESP-01S modules. With onboard USB-to-serial (FT232) chip and reliable connectivity, it simplifies firmware flashing and communication tasks. The ESP-01S version comes pre-equipped with a 10K pull-up resistor for enhanced stability, making it highly recommended. Operating at 3.3V, it supports 1MB SPI flash, an onboard 3dBi antenna, and a user-friendly pin layout. Whether for IoT prototyping, sensor integration, or wireless control, this adapter ensures efficient performance with solid build quality, quick setup, and reliable operation for hobbyists and developers alike.

This Arduino Uno is an Official microcontroller board from Arduino officials based on the ATmega328P. It has 14 digital input/output pins (of which 6 can be used as PWM outputs), 6 analog inputs, a 16 MHz quartz crystal, a USB connection, a power jack, an ICSP header and a reset button. It contains everything needed to support the microcontroller; simply connect it to a computer with a USB cable or power it with an AC-to-DC adapter or battery to get started.. You can tinker with your UNO without worrying too much about doing something wrong, worst case scenario you can replace the chip for a few dollars and start over again.

Pro-Range Raspberry Pi Pico does not require a particular introduction because it has already gained popularity due to its revolutionary size, low cost, and variety of possible project applications. For beginners learning microcontroller programming with this powerful Single Board Computer is now super easy, cheap, and resourceful. whereas experienced users can take advantage of the Raspberry Pi Pico’s rich peripheral set, which includes SPI, I2C, and eight Programmable I/O (PIO) state machines for custom peripheral support. Pico, which can be programmed in C and MicroPython, is adaptable to a wide range of applications and skill levels, and getting started is as simple as dragging and dropping a file. So, order your Raspberry Pi Pico and other necessary components in our high-quality Pro-Range Basic Raspberry Pi PICO kit in which we’ve included the PICO board, 30cm USB to Micro-USB cable, 300 Point breadboard, and 10 pin male to female jumper wires.